Headlight Size

Mitsubishi Lancer Headlight Bulb Size


Mitsubishi Lancer Headlight Bulb Size Chart

*Headlightsize is reader-supported. When you buy through links on our site, we may earn an affiliate commission.

2017 Mitsubishi Lancer ChartBuy Bulb on Amazon
Headlight Bulb High Beam and Low Beam
D2S
Headlight Bulb High Beam
9005
Center High Mount Stop Light Bulb
LED
Brake Light Bulb
7443R
Turn Signal Light Bulb Front
7440A
License Plate Light Bulb
2825
License Plate Light Bulb
98
Daytime Running Light Bulb
LED
Turn Signal Light Bulb Rear
7440
Back Up Reverse Light Bulb
7440
Side Marker Light Bulb Rear
2825
Side Marker Light Bulb Rear
98
Parking Light Bulb(with halogen headlights)
2825
Parking Light Bulb(with halogen headlights)
98
Side Marker Light Bulb Front(with halogen headlights)
2825
Side Marker Light Bulb Front(with halogen headlights)
98
Parking Light Bulb(with HID headlights)
LED
Tail Light Bulb Inner
2825
Tail Light Bulb Inner
98
Tail Light Bulb Outer
7443R
Side Marker Light Bulb Front(with HID headlights)
2827
Trunk or Cargo Area Light
DE3022
Dome Light Bulb
DE3175
Map Light Bulb
DE3175

Mitsubishi’s Lancer is a car that has been in production for four decades.

Throughout its history, it has been known as a well-rounded performance vehicle. In the past few years, Mitsubishi has struggled to stay afloat in America and Europe where they have faced increased competition from smaller Japanese automakers such as Mazda and Honda.

Despite this, they have begun to struggle in the East as companies like Hyundai have increased their market share.

The Mitsubishi Lancer was produced in 1973. It has been marketed under different nameplates in different parts of the world. Such names include Plymouth Colt, Chrysler Lancer, Hindustan Lancer, Eagle Summit, and Colt Lancer.

The first models featured halogen light bulbs which have been replaced with LED and HID headlights for recent models.

Bulbs used

For the 2017 and subsequent model years, the Mitsubishi Lancer comes with a D2S bulb for its high beam and low beam headlights. Some models use the 9005 bulb for the high beam. Mitsubishi uses LEDs for the car’s daytime running lights and parking lighting.

Upgrading from factory bulbs to aftermarket LED/HID

When upgrading from your factory bulbs to aftermarket LED/HID bulbs, it’s important to check the bulb sizes to ensure that they match. You want your new bulb to work with the existing headlight assembly without needing any modification. This ensures that you have the right fitment with the right power requirements. In the end, you get a fitting that illuminates light as required and does not compromise safety.

Advantages of upgrading from halogen to LED/HID technology

  1. LEDs and HIDs are more efficient as they produce more light and less heat.
  2. Extends lifespan.
  3. Improves driving safety at night.
  4. Easy to install
  5. HIDs and LEDs give your car a better look as they are aesthetically appealing.

How to choose the correct bulb size for your LED/HID lamp

Our online light bulb chart helps to determine what bulb size is right for your Mitsubishi Lancer. All you need to do to access this information is to specify the year and trim specs.

  • Mitsubishi Lancer user manual

Your vehicle manual provides important details that come in handy when you want to replace parts on your vehicle. Such parts include headlight bulbs. Depending on the vehicle you have, the bulb size details may be located in the Vehicle Maintenance section.

  • Check your original bulb size

All bulbs should have their sizes indicated on them. As such, you can take a look at your old bulbs to check for their size/part number. This should guide you in choosing the correct bulb size for your LED/HID lamps.

  • Contact your dealership

You can also reach out to your vehicle manufacturer or dealership for help. They should be able to give you the correct size/part number for your bulb.

Installing new bulbs

Installing new bulbs is a simple process, but there are some important items to be aware of in the course of your installation.

When installing any bulb, do not touch it after the purchase with bare hands.

The oil from human skin will cause the bulb to fail early when in operation. If you need to clean off dirt or another buildup on the bulb, use rubbing alcohol or soap and water instead.

Also, make sure you are using the specific bulb for your current model as some auto parts stores offer universal alternatives that may look similar but have different electrical connections.

Installing new headlight bulbs requires removing the metal casing on top of each light housing by unscrewing them from above and then pulling them straight down.

This will expose the wiring within that connects the lights to the car’s electrical system. Locate these wires and disconnect them by gently prying apart the metal tabs on either side of the connectors with a small screwdriver or another thin tool.

After both connectors are unplugged, pull upwards on each light bulb while rotating it to unlock it from its housing.

The new bulbs must then be installed in reverse order of removal, making sure they lock into place when slipping them back into their respective housings.

Once this is done, you can use your fingers to slide on new light coverings over the top if desired before tightening them down with your hands or a small wrench or pliers.

When the time comes to turn on your headlights, you may need to wait up to fifteen minutes for them to fully warm up. If they are still not working after this time, you most likely have installed faulty bulbs or fuses and will need to switch them out or check with an expert mechanic.

If you install new lights yourself and find that they do not work correctly, simply reverse the process with any standard bulb of the same type in order to put the old ones back into place.

It is important to make sure you do not touch these bulbs unless they are faulty.

If your lights are operating incorrectly or burnt-out despite the fact that you have replaced both headlight bulbs, it may be time to inspect your entire electrical system for leaks or other malfunctions.

Additional equipment needed

You may need the following tools when installing new bulbs:

  1. A screwdriver
  2. Wipes and tissues to clean the new bulb
  3. Electrical wiring just in case you need to replace wires

Q&A question

Where should my headlights be aimed?

When illuminating a wall, your low beam should start slightly below or at the top of the center of the headlight lens. The light pattern may be higher on the right passenger side and lower on the driver’s side.

Generations

  • 1988–2003: Mirage-based Lancer
  • 2000–2010
  • 2007–2017
  • 2017–present

See Also:

Mitsubishi Lancer Wheel Size

Mitsubishi Lancer Tail Light Bulb Size


Leave a Reply

Your email address will not be published.